After fitting a new crank I have a problem aligning it with the clutch. There is no white dot on the old clutch. During strip down I only marked the clutch together with the prime gear and not the crank shaft, so I cant use the old parts as a reference.
The pics in the workshop area are not much good since they have been resized and cut in the edges.
The shaft that the clutch is fitted on is not totally symmetrical since there is a little "cut" in the edge, and the clutch itself is not either symmetrical since there are 6 symmetrical "holes" and one extra, in between two of the other holes.
I have marked the "symmetrical divergences" with a red line. How should these red lines be in comparison to each other to align the clutch with the crank.
_________________ MC21, GP-Replica (Daijiro Kato, Telefonica Movistar Team 2001)
I wouldnt worry, I did a Dry clutch conversion and had the same problem, im not sure what that's all about, Just slip the clutch on, Mine had no problems at all and no marks!, and when i asked the same question i dont think there was a concrete answer...
if someone wants to correct me then please go ahead!! but i think youll be fine!
Also realised that the shaft going to the gear box have nothing to do with the alignment since there are bearings between the shaft and the clutch (of course, otherwise there would be no need of a clutch). _________________ MC21, GP-Replica (Daijiro Kato, Telefonica Movistar Team 2001)
I don't understand the whole white dot thing. I don't see how it can be important. _________________ james
Its not how fast you go...Its how you go fast.
MC21 Rothmans
RS250
RC31
CRF250X
748R
Porsche (many)
http://members.rennlist.com/j911brick/rennlist3_002.htm
Is I see it there is no need for alignment like in 4-strokes, regarding to timing of the cam, but needed when it comes to "balance". The clutch will spin pretty fast, and if it is not "balanced" together with the crank I guess there could be some nasty vibrations. Maybe the "unbalance" of the clutch is supose to take away the "unbalance" of the crank. Most single cylinder engines has a balancer shaft, maybe the clutch on the NSR corresponds to such a thing...(seems strange though since the clutch wont spin with the same frequency as the crank).
If everything was balanced directly from the factory then there would be no need to align, so the white spots must mean that the clutch is not perfectly balanced. At least thats how I think. _________________ MC21, GP-Replica (Daijiro Kato, Telefonica Movistar Team 2001)
Yeah thats what i was thinking.........However, pull the clutch in and its ballance has now changed........ the iner stops/slows as the outer maintains its speed from the crank... release and its now diffrent as the gearbox shaft is in a diffrent location!!!
Slap it in..... If its wrong Blame Andy!!! LOL
When i took the wet clutch out i had NO marks at all....
I've rebuilt one....no maybe two NSR250 engines and I don't think that I've ever paid any attention to any white dots.
Let's have a look at it logically.
The engine doesn't have a balance shaft, so there's nothing to align there. The primary drive gear fits on splines to the crank. there's no missing spline to locate it so it can be fitted in any position. It has no lightening holes, or offset weights so chances are the COG is pretty much in the centre. If exact rotational location was necessary then Honda would have made it fool proof and punched or scribed a permanent mark of some sort.
The primary drive gear drives the primary driven gear on the clutch at a ratio of 2.36:1 (MC21) or 2.5:1 (MC28), so if you align anything statically then after 1 revolution of the crank you're gonna be miles out, so obviously nothing needs aligning there. You can see that the 28 would requires 5 revs of the crank to line up the dots again. The MC21 would align every 59 revolutions.
Other gears attached to the primary are the same story.
The answer is, throw it together and don't worry. If it vibrates then something else is wrong. It's not due to misalignment of the gears .
There are a lot of little things on the main site that need updating, it was essentially written 10 years ago after all, and contrary to popular belief I wasn't actually as perfect back then as I am now!
I'm pretty confident that there is nothing dangerous on the site though, old erratum's included. _________________ Andy.
NSR-WORLD.COM
Please keep all responses to Forum posts on the Forum so that others may benefit.
Please DO NOT PM me for technical advice. My time is precious, and you will probably receive a faster response on the Forum anyway.
Andy wrote:I'm pretty confident that there is nothing dangerous on the site though.
not if you work in a replating plant anyway;
the tuning section wrote:run the bike flat out in top (6th) gear, near the "red-line", i.e., 12000rpm, for at least 10 seconds, preferably slightly uphill
Well, that will establish if you're in the least bit lean, try it in the cool of dawn for a best reading. _________________ Please do not PM me technical questions, if you can't find it on the Forum start a thread
To be fair, both myself and Andy hold ours flat out for well over a mile each time we ride them. And I mean proper flat out! _________________ If I have to take the carbs off once more...
It's just a little over that with a quick action throttle Maxim!
The "chop straight" is great isn't it Steve... we laugh about it every time we get to the end of it! About 2/3 of the way down you can hear the motors just won't rev any more, and the 30 limit signs/pit lane turning are still some way away yet! _________________ Andy.
NSR-WORLD.COM
Please keep all responses to Forum posts on the Forum so that others may benefit.
Please DO NOT PM me for technical advice. My time is precious, and you will probably receive a faster response on the Forum anyway.
lol, yeah Ive often thought, damn... its still a long way to go and I'm already flat out.
1 and 2 and 3 and 4..... lol its still a long way to go.... 5 and 6...7...
My fingers start to tingle at the tought of full bore for more than 30 seconda at a time. _________________ If I have to take the carbs off once more...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You cannot download files in this forum