she runs

**Sat Nov 25, 2006 5:51 pm » Post: #1 » Download Post**

Firstly i'd like to thank Andy for all his help with parts identification and advice,rebuild went ok today despite the weathers best efforts to delay things,theres nothing like trying to assemble top ends outside in the rain Evil or Very Mad

is there?
Wiring and plumbing went ok,thanks to Honda for making things workoutable when you have forgotten where everthing goes!
She started almost straight away and sounds so much crisper,if only i had not lost rc valve l/h threaded nuts i could have ridden her,oh well i'll have to wait.
cheers rob.

**Fri Dec 08, 2006 7:49 pm » Post: #2 » Download Post**

i stuck her on the dyno today,she made 46.6 at the back wheel after adjusting powervalves properly me and the tester were well pleased.
They are a company called stinkwheels in Essex tel 01708 372122,i think these guys deal incorperate Gibson exhausts aswell,gonna get them to make me a set of pipes up.
cheers Rob

**Fri Dec 08, 2006 8:24 pm » Post: #3 » Download Post**

Is that with the MC16 or MC18 barrels, I would of been hoping for quite a bit more if the '18 barrels are fitted.

Jeff managed to get 43.5 out of a set of stock MC16 carbs and barrels.

If the '16 barrel are fitted then its very good!
_________________
If I have to take the carbs off once more...

**Fri Dec 08, 2006 10:30 pm » Post: #4 » Download Post**

mc18 cylinders.mc16 carbs and pipes,i didn't think this was too bad for an old shitter Shocked

steve,are power figures at crank or back wheel for jeff?

**Fri Dec 08, 2006 10:51 pm » Post: #5 » Download Post**

All HP figures on NSR-World are rear wheel.
_________________
If I have to take the carbs off once more...

**Fri Dec 08, 2006 10:51 pm » Post: #6 » Download Post**

Dump the MC16 carbs and fit MC18 ones! You'll soon be heading towards late 50's I would say.

You may find you need a set of MC18 pipes too.
_________________
Andy.
NSR-WORLD.COM

Please keep all responses to Forum posts on the Forum so that others may benefit.

Please DO NOT PM me for technical advice. My time is precious, and you will probably receive a faster response on the Forum anyway.

Check us out on Facebook! Please "like" our page!

**Fri Dec 08, 2006 10:57 pm » Post: #7 » Download Post**

im looking for 18 carbs.have you got any Andy? i saw Jamie has some for sale on his site will these be suitable? pipes i'm gonna get made by gibson
cheers rob

**Fri Dec 08, 2006 11:09 pm » Post: #8 » Download Post**

There are often '18 carbs for sale on ebay going for between £20-£40 per pair.
_________________
If I have to take the carbs off once more...

**Fri Dec 08, 2006 11:25 pm » Post: #9 » Download Post**

if i could get some for that i'd be a happy man,she did seem to run very well though,is it possible just to alter jetting temporarily for now, gonna get an mot tomorrow.winter what winter Laughing

**Sat Dec 09, 2006 1:19 am » Post: #10 » Download Post**

You're never going to get great power out of the MC16 carbs unless you have the F3 variants. The MC16 carbs are only 28mm, but the MC18 and MC21 carbs (which are similar) are 32mm.

I think I may have a spare set of MC18 carbs, but you'll need a manifold too.
_________________
Andy.
NSR-WORLD.COM

Please keep all responses to Forum posts on the Forum so that others may benefit.

Please DO NOT PM me for technical advice. My time is precious, and you will probably receive a faster response on the Forum anyway.

Check us out on Facebook! Please "like" our page!

**Sat Dec 09, 2006 6:38 am » Post: #11 » Download Post**

If you could find them for me Andy i would be grateful,this will be my last post for a while as my connection is down,stay safe everyone.
cheers rob